11/23/2023 0 Comments Build wood shelf bracketsApply an even coat of stain to the 1x12s using a new blue shop towel.With gloves still on, open up and stir your can of stain with a wooden paint stir.Note: as mentioned in Step 4, we stained our full length, uncut 1x12s before cross-cutting to length to save time. 2-4 coats should suffice, allowing 1 hour dry time between coats. Shaking your hand back and forth while applying will form drips and inconsistencies. Make sure to complete uninterrupted left-to-right and right-to-left passes. Apply a thin, even coat at 10 to 16 inches away. Do a light sanding with 220 grit sandpaper. Post up on some newspaper or old plywood. For a strong coat, choose an enamel paint. Depot was mostly out of black brackets, so we bought gray brackets and spray painted them black. Note: now is a fantastic time to spray paint your shelving brackets if necessary. After 15 minutes, be sure to remove ALL pre-stain on areas that are still moist.Wait about 15 minutes to allow the pre-stain to fully penetrate the wood grain.Apply a generous amount of pre-stain to the wood, rubbing it in and wiping off the excess. Snag some nitrile gloves, shop towels and your 1×12 boards.Open your pre-stain and stir with a wooden paint stirrer for at least 1 minute.Pre-staining two pieces is much faster than pre-staining four pieces. Note: we pre-stain our full length, uncut 1x12s to save time. When your standard cordless drill/driver wears out on a lag screw, install it with an impact driver. It’s the cordless drill with enormous amounts of torque, aka rotational force. Lint heavy materials will end up covering your wood stain with thousands of tiny paper fibers. The lint level of a standard paper towel is through the roof. Wouldn’t any old paper towel work? No way. Pre-stain helps the wood absorb the stain more evenly, resulting in a more even coat. Softwoods like pine do NOT absorb stain evenly, resulting in a splotchy, streaky, uneven pigment. Is it really necessary? The answer is yes. We needed the peace of mind that anything we store on our shelf will hold without question. Why lag above a standard thickness screw? Structural integrity. Be sure to borrow the tools you don’t currently have if you need to assess their long term value to you.If you’re a regular DIY kind of human, do you have some leftover pre-stain wood conditioner? Mid-tone wood stain? Shop towels? Gloves? Any extra 1 inch thick common boards to use for your shelves?.Before you take a trip to the hardware store, inventory the materials and tools you already have.We love the contrast of the white and black along with the natural wood tones. These are offset by our DIY pallet wood crates set upon the shelves to hold laundry room accoutrements. With white shiplapped walls, we decided on black brackets and black pipes to support clothes hangers for contrast and a gray and white patterned floor tile.Varathane’s Early American offered a mid tone brown that offered visual juxtaposition against the white shiplap but isn’t too dark. We installed DIY shiplap that we painted white. If you love the modern farmhouse vibe, we recommend choosing a stain that contrasts your wall color.Already have the pre-stain, stain, shop towels & nitrile gloves? (2) 1x12x10 + (10) 10” x 8” black medium duty shelf brackets + 1/4″ x 3” lag screws + #6 x 1/2″ hex screws….Varathane Early American wood stain + blue shop towels + nitrile gloves… The hammering feature installs screws when clutched drill/drivers fail, ensuring NO stripped screws. Stop pre-drilling and use this impact driver’s ENORMOUS amounts of torque for ALL common board to common board applications. Nut drivers (bits) for the lag screws & 1/2″ long hex screws.Impact driver (or) corded drill/driver with a clutch. We bought gray brackets and sprayed them black.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |